Home > Not Detected > MAXTOR SATA 300GB HD Not Recognized By BIOS.

MAXTOR SATA 300GB HD Not Recognized By BIOS.

Contents

Then I downloaded and ran your Capacity restore tool, and it showed the correct HD capacity difference so far so good! Favorite MFM/RLL drive was a Mitsubishi MR-535. 5.25" half height, 60MB RLL/40MB MFM, voice coil actuator, very quiet, and reliable as heck. my 1 TB harddrive which had all my data on was reporting on 33 MB and coming up as RAW in Windows. I took it back to Frys to have them replace under my extended warranty. get redirected here

USB mass storage is not going to be supported since it simply does not allow the protocol that we are using to access the hard drive. February 11, 2012 Dave Well, my suggestion would be a new computer. I can use back my hard disk Hitaichi and WD with out problem.... I took it apart and reset the hdd as recommended but that did nothing. http://www.techspot.com/community/topics/maxtor-sata-300gb-hd-not-recognized-by-bios.18228/

Hard Disk Not Detected In Bios

Thank you so much for freely distributing this siftware. WHile the drive was recognized I promptly used Seagates DiscWizard and set it up for a 10GB and 150GB partition NTFS. Now was the time to do the final load on the other disc setting the BIOS to AHCI the other options on the board are IDE and RAID I think my If this doesn't work, you can try going to the manufacturer's website and get the breakdown of Sectors, Cylinders, etc and manually input the figures.

Anybody try this? Maybe it's your power supply or something. From here, you can partition and format the drive. Hard Disk Not Working I would also consider a BIOS update.

They are cheaper also. External Hard Drive Not Detected Any ideas, but please explain how to do things clearly if you reply, many thanks. It worked perfectly. Since my installed Master was a Maxtor 6L040J2, I thought cloning my slave would make plug and play a breeze because the BIOS and driver information had already been installed?

i literally spent hours trying to recover my hard drive. Hard Drive Not Showing Up In Bios Never disconnects spontaneously or anything like that. The problem started as soon as I installed the 160GB SATA HDD replacing my 2 PATA drives (30GB Maxtor, 40GB Maxtor). This might be a motherboard problem, but it might also be a power supply problem.

External Hard Drive Not Detected

IMPORTANT: If Pin 11 is not connected or connected to power supply, that means that "Staggered Spin-up Detection" is enabled, & your HDD will NOT be recognized or not recognized all Any suggestions? Hard Disk Not Detected In Bios Drive diagnostics should verify that drive is operational. How To Repair Hard Disk Not Detected i tried in another PC, had swapped every cable and tried in several OS..but result it same… is there anything with the harddisk logic card or its firmware??

Any ideas ? http://vgvinc.com/not-detected/hard-drive-recognized-by-bios.php I tried 20 different softwares (at least !) since 3 days and you gave me back my 48 missing Gb in only 10 seconds ! My motherboard is a Gigabyte GA-K8NF-9. Capacity should be 160G. Internal Hard Disk Not Detected

Your name or email address: Do you already have an account? Unplug them and try a different SATA port and or power cable. Went to My Computer there was still no F: Drive but the C: Drive properties showed both drives listed… only I couldn't figure our how to access the second drive and useful reference Or should I just make another partition and run the program from it?

My ‘system Device Info' says ‘none' for Primary Hard Drive. Internal Hard Drive Not Detected I don't know your mobo so you'll have to work out which end is slot 1 and which end is slot 3. The internet buzz said to experiment with increasing stack register settings caused by certain programs: Acronis and Norton were listed among them… I'd been running Norton forever with no problems so

I downloaded this tool and I am getting a message when I click on the desired hard drive, that there are two devices on a single channel.

Connect with top rated Experts 22 Experts available now in Live! Powered with <3 from Vanilla & WordPress. Cables are always double-checked to be firmly pushed in and yes the 300G drive is spinning... Hdd Not Detected In Bios Fix I was able to partition the HDD (12GB and 140GB) and am currently installing XP onto the 12GB C: partition.

Yippee! That's if you have more than one SATA drive and are using them as a RAID array. When I went to My Computer… the anticipated new Drive: F still wasn't there? this page It restored my 1Tb Disk instantly.

i still don't understand why it still does that. I strongly recommend to re-power your computer before running this tool. As a last resort, you can try either manually typing in the cylinders, sectores, etc instead of having the BIOS auto detect it. The system has been rock stable for over a year with 2 PATA HDDs.

The other one is blank . Managed to reset disc first by zeroing it with WD utility followed by old Maxtor utility used this method twice unfortunately on the third attempt it failed to work whether I This needs fixing before any machine will recognised the drive. Sometimes there is info on the drive that the recovery disks look for when installing.

Please select a hard drive from the list of drives." Is this the issue of swithching the type of SATA ports in the BIOS? By the way I can use this drive as external drive and it spins as well. Breakout boxes, switches, a bunch of old hard drives (need a 5.25" MFM drive ??), floppy drives (except 5.25" or 8" -- both of which I now wished I'd kept one After the clone the disk showed as a 32Mb Drive.

Actually, I'm not sure why I have 8 computers!! (in fact I just tossed out that number w/out really thinking about it -- read on !! Still needed for RAID, but makes life simpler on single drive systems. 0 LVL 3 Overall: Level 3 Hardware 3 Components 2 Message Expert Comment by:Lanadmin_cam ID: 151571852005-10-25 Yess agree Therefore capacity cannot be recovered. the only differences are the size [120g v.s 300g] and buffer [8mb v.s 16mb] You may be onto something there though, as it is set on AUTO detection...will have a look

Bottom line for a WD SATA drive. So if you're a guest at my house you can jump on the internet &check your e-mail, etc. Because this pin 11 is reserved for future use by SATA specifications, many SATA power cable manifacturers leave this pin going nowhere instead of grounding it (because it is not supposed from the guest bedroom :) I have spent a few $$ to add monitors, etc. (I've been given several CRT's -- but generally toss those &buy an LCD instead).

Hitachi's Feature tool was crashing when trying to enter Capacity menu, but this little great tool restored disk back to useable state and data is safe! but once I powered down the machine for a while, powered back on and again same problem.