Home > How To > Hardware Problem Installing 2nd Drive

Hardware Problem Installing 2nd Drive

Contents

successfully installed second hard drive thanks to this post 🙂 Reply Joe says: August 23, 2009 at 11:14 am I have a 320 gig IDE hard drive .Im trying to install Sometimes, though, the power connector can become stuck. Well it sounded so simple but no matter what I do I cannot get the computer to recognize my old drive connected to the slave connecter on the cable. If this article is too hard for you to understand, then perhaps you should look for another article somewhere else or wizen yourself up a little and come back for more. navigate here

The HD is powered on and I think it is properly connected. When replacing it I noticed the other cables, such as one going to my CD drive have a "300 v" text on them. The first hard drive is SATA, the second which came from an older computer is IDE. Mr1000lbDec 26, 2015, 2:48 AM Hi, In my case I have my PC since last year. http://www.howtogeek.com/74814/hardware-upgrade-how-to-install-a-new-hard-drive-pt-2-troubleshooting/

How To Install A Second Hard Drive

With the drive seated, insert and tighten two screws for each of the broad sides of the drive cage. But having read this article in advance, I felt confident I could have overcome installation issues. The hard drive that the system boots from is usually the primary master. And whats acpi?

Very helpful!! All Rights Reserved. Entertainment Sling TV vs. Sata To Usb For a couple of reasons, I have decided to mount the drive inside my PC.

So, in the case your new HDD has no active partition (windows is not installed in it – it is used as an internal flash drive for storage purpose), I personally You may require an updated BIOS to use your drive, and you’ll have to check the manufacturer of your motherboard to find out where you can update it. The SATA power connectors are manufactured with an extended ground pin which ensures that ground is always connected first, allowing it to be connected and disconnected safely while running.The 1.5 TB http://www.tomshardware.com/forum/285014-32-problem-installing Very helpful!!

The maintenance manuals, however, should clearly specify that disks must be converted to dynamyc, and they don't.Thanks again for the tip!!furosa 0 0 « Message Listing « Previous Topic Next Topic Ide Cable Do I need to change this,to another value? Before installation, inspect the inside of the computer's case and determine where you want the drive to go. Both drives should be listed on the opening screen.

How To Install A New Hard Drive Windows 7

In that case, there may be another option to select one drive over the other:But what if one of the drives doesn’t show up at all? Likewise, bus speed should be taken into consideration when buying a new RAM. How To Install A Second Hard Drive Reply Wayne McFarland August 6, 2015 at 11:37 am My motherboard has four ports that are taken by the OS SDD, a HDD, the DVD drive and the front card reader Sata Cable the one in the pc is 5v and 12v ,the one i wont to hook to the pc is 5v Reply James Bruce December 31, 2015 at 2:02 pm The power

Installing Second SATA HD Help...Installing second HD Installing a second HD installing on second HD? check over here The drive is a SCSI. Thanks Reply Tom says: December 20, 2008 at 10:19 pm Without getting involved in a conversation about whether or not myself or anyone else can understand the lingo here…I'm simply attempting Ensure the particularly SATA port that the HDD is attached to has hot swap enabled.2. (optional) Connect the SATA data connector to the 1.5TB hard drive but leave the power connector Mbr Vs Gpt

What are the options .. Next, follow the SATA data cable (not the power one) to the motherboard, and have a look at where it is plugged in. Reply Michael Negranol says: July 28, 2008 at 11:56 pm A very helpful article, really. his comment is here Send your query to [email protected]]Chances are that your PC is treating the new drive, which I assume has no operating system installed on it, as the boot drive.Once upon a time,

Im very sure I have it connected correctly, but when I boot up and try to enter the setup it takes a very long time and eventually goes black bar a Reboot And Select Proper Boot Device If not, you’ll have to find or buy some hard drive screws. Let’s do this! 1.

Reply James Bruce August 7, 2016 at 9:14 am There is no magical software.

Reply Alan Bush says: November 26, 2008 at 11:12 pm At last!! It had windows 2000 on it and i just want to save home movies on it. thanks, Spiv Reply israel says: March 3, 2008 at 12:59 am ------HELP PLEASE----- i am putting a unpartioned hard drive in my computer as my slave hard drive. How To Enter Bios Reply Alejandro says: August 3, 2008 at 8:19 pm I Have A Compaq Presario SR5130NX with a Western Digital Caviar SE (SATA) Hard Drive (Vista).

I'm somewhat of a techie and i do understand all the jargon. He tried using his Windows backup disks that he made when he bought the laptop but it goes through the disks, has him restart and then still just states no operating Thanks for the easy to follow instructions. weblink Reply Cliff says: December 11, 2008 at 3:23 pm Dave, Thank you for taking the time and making the effort to publish these instructions.

I just don't know enough to understand where the hang up is. If it boots fine with one drive and not with two, you’re probably overloading the power supply. I’ll be covering the software and configuration side of adding a second drive in my next article – so stay tuned for that.