Home > Hard Drive > Hard Drive Showing As Primary Slave?

Hard Drive Showing As Primary Slave?

Contents

New hard drive is seagate. The Master drive goes on the black connector at the end of the cable, the slave drive connects to the gray connector in the middle and the host adapter connects to install and open - Do not run bench marks.Look in the upper right, should see:msahci OK. TechSkillsVideos 215 411 visningar 9:41 How to recover data from a hard drive (stuck heads: buzzing, clicking, etc) - Längd: 10:28. http://vgvinc.com/hard-drive/how-to-set-up-old-hard-drive-as-primary.php

djaliplumeJul 19, 2011, 1:02 AM Hi. It is also a good solution for backing-up files. DELETE all partitions. My hard drive is slow: Make sure you have your CD/DVD drives plugged into a different channel/cable. page

Master Slave Hard Drive Setup

I have a 2tb Western Digital drive (partitioned into smaller disks) as Primary Master on Channel 0 and a DVD drive as Primary Slave. Join the community here, it only takes a minute. I bought another SATA hard drive.

Läser in ... Wikipedia Link - Serial ATA At the device level, SATA and PATA (Parallel AT Attachment) devices remain completely incompatible—they cannot be interconnected. For example, a modern SSD is likely to support the SATA III standard, also known as SATA 6.0Gb/s. Master Slave Hard Drive Sata by R.

Logga in Transkription Statistik Hjälp till att översätta 158 021 visningar 177 Gillar du videoklippet? How To Slave A Sata Hard Drive DO NOT put a CD Drive on the same channel as your hard drive! In one of my Hard drive, boot sector went bad. http://www.tomshardware.com/forum/271406-32-installed-secondary-slave-problem Privacy Policy | License | Terms & Conditions | Uninstall | Resource | Data Recovery Solution | iPhone Recovery | Android Recovery MESSAGES LOG IN Log in Facebook Google Email No

solved install a secondary ssd for booting windows?? How To Install A Second Sata Hard Drive In Windows 7 But here we are. Yes, my password is: Forgot your password? Cloves 123 800 visningar 2:19 Computer Hardware Basics : How to Make a Slave Hard Drive - Längd: 1:23.

How To Slave A Sata Hard Drive

Normally it's red on the grey cables and white on black cables etc there will be some kind of colored line to indicate pin 1. http://www.wikihow.com/Configure-Master-and-Slave-in-BIOS-for-Two-Hard-Drive-Disk-in-a-Single-System Main Sections Technology News Reviews Features Product Finder Downloads Drivers Community TechSpot Forums Today's Posts Ask a Question News & Comments Useful Resources Best of the Best Must Reads Trending Now Master Slave Hard Drive Setup The largest I've seen is 16 or 32 gigs.Before swapping cables out. Master Slave Hard Drive Jumper Settings Is the full capacity of the hard drive being seen: Verify the BIOS has auto-detected and LBA mode is enabled.

When you try to install a really big hard drive into a lot of older systems, you'll find that the BIOS is only capable of seeing 137 GB. check over here Arbetar ... A few years ago, before SATA, adding a second hard drive was made more complicated due to the fact that PATA (also known as EIDE) required a master/slave relationship. And to be honest I don't care about squeezing every last bit of speed out of the drive. What Is A Slave Hard Drive

Two if you're lazy and only screw things in on the side. If you're opening up something an OEM machine you could be voiding your warranty so check first. Transkription Det gick inte att läsa in den interaktiva transkriberingen. http://vgvinc.com/hard-drive/making-sata-primary-driver-when-it-is-my-only-hard-drive.php TechSpot Account Sign up for free, it takes 30 seconds.

Om Press Upphovsrätt Innehållsskapare Annonsera Utvecklare +YouTube Villkor Sekretess Policy och säkerhet Skicka feedback Testa nya funktioner Läser in ... Sata Master Slave The master can also be referred to as the "primary" drive with the slave being the "secondary". Cable-Select Option (Default) - Use with Ultra ATA cables.

My cd is set to cs and has its own cable on master Jan 2, 2007 #3 Tmagic650 TS Ambassador Posts: 17,244 +234 Change the hard drive jumper to

At the application level, SATA devices can be specified to look and act like PATA devices.[29] Many motherboards offer a "legacy mode" option, which makes SATA drives appear to the OS Down load As-SSD. Most likely you set your jumper wrong. Sata Hard Drive Slave Jumper Setting Once reported, our moderators will be notified and the post will be reviewed.

Flag Permalink This was helpful (0) Collapse - Drive runs fine in a friends computer... by scoobi69er / June 8, 2005 9:09 PM PDT In reply to: (NT) Points to bad cable or drive. I guess I'll have to dig further. weblink Do not concern yourself with the Windows Experience Index.

This allows the cable to select if the drive is master or slave based on the position on the cable. Maybe it's not the SSD that's causing the laggy feel then. Ben Avery 11:37 29 Dec 03 G'day mate,good to see you are firing on all cylinders as usual with your rapid replies!I checked the jumpers before I even thought about posting, benicellguy 7 044 visningar 9:13 Installing a 2nd Hard Drive - DIY Video Guide - Längd: 6:49.

Most boards have 2 channels while 4 is becoming more and more common at least on the higher end boards. Rankning kan göras när videoklippet har hyrts. Did this article help you? Recomendations sometimes diff between Amd and Intel MB.How full is your SSD.Have you disabled Hibernation.

To get around this you'll want to use that install disk that came with the hard drive or if you're a relatively advanced user a BIOS update should be available. Tom's Hardware Around the World Tom's Hardware Around the World Denmark Norway Finland Russia France Turkey Germany UK Italy USA Subscribe to Tom's Hardware Search the site Ok About Tom's Hardware EDIT Edit this Article Home » Categories » Computers and Electronics » Hardware » Internal Components ArticleEditDiscuss Edit ArticleHow to Configure Master and Slave in BIOS for Two Hard Drive Disk It's more that slight unresponsive feeling I get.

Now you should be able to find an open 3.5" slot somewhere. I looked in my bios and saw that it was set as Primary Slave on IDE Channel 1. expertvillage 425 216 visningar 3:24 How to Install Internal Hard Drives : Setting Up Pins for IDE Hard Drives - Längd: 2:22. You can change this preference below.

Open up your computer case. With SATA, all you need is a free SATA port on the motherboard, a spare bay in which to mount your second hard drive, and a SATA cable to connect the Usually the first BIOS screen to appear is the primary, or basic screen. 4 In the CMOS menu, find "Hard Disk" and then the "Primary Master" selection. Försök igen senare.