My primary hard drive is a Seagate 200GB SATA (ST3200822AS) and I have Windows XP MCE 2005 SP2 running off of it. This is needed because most BIOSes will disable HPA/DCO operations to ensure that nothing can reset or damage that hidden area. decaFeb 2, 2010, 6:58 PM 1. why was is shipped from Samsung like this?Tom Walter on July 15, 2008 8:53 pm Encountered odd problem and tool didn't even recognize drive. http://vgvinc.com/hard-drive/is-it-hard-to-just-replace-a-sata-hard-drive.php
AnonymousJan 18, 2010, 9:40 PM Paperdoc said: The problem may be you're not looking in just the right spot . Do you plan to move your OS to the new int and make it your boot drive? It just allows you to restore that capacity in case other software or PC distributor reduced it. Will this program work to fix that, or do I need something else? http://www.techspot.com/community/topics/getting-mobo-to-recognise-unformatted-wd-sata-ii-hard-drive.72009/
PaperdocMar 23, 2010, 8:02 PM ethicalid, what you describe MAY be a hard drive with significant problems. RIGHT-click on the Partition and choose to Change its Name. All hdd mfg have this software, which is why you need to get it from the hdd mfg website. Hard Drive Detected In Bios But Not During Windows 7 Installation Give us a few of these answers for info, and try the Seatools for DOS diagnostics and tell us its output.
It's not automatic."Or, as I thought, install the eSATA adapter into the pc, connect it to the other SATA connector, which is underneath the SATA connector that my internal drive is Second Hard Drive Not Showing Up In Disk Management On its left end is a smaller label block with things like "DISK_0", a size, and a few other bits of info. I am on ultra thin Acer Aspire S3, where removing disk could be quite a challenge. http://newwikipost.org/topic/AcuhzifZlCLyK03liQEgkavV7P28vESY/Trouble-migrating-an-IDE-drive-to-SATA-mobo.html In-depth disk diagnostics, disk duplication and wiping, firmware and file recovery.
Oct 30, 2006 Cannot install Windows on WD 500GB SATA hard drive! Hard Drive Shows Up In Bios But Not Disk Management Windows 10 KendracFeb 24, 2010, 4:32 AM I am having a similiar problem except my D: drive which I have been using for a long time stopped showing up. Worked like a dream where all others had failed. It worked perfectly.
reconnected it via SATA and same story. It turns out that my WINDOWS drive(Drive G: WD 1TB SATA) and 1 other of my WD 1TB storage drives are now showing as nonformatted when I plug them in via Hard Drive Shows Up In Bios But Not Disk Management Can this be resolved?johan verbist on November 9, 2007 6:23 pm HI, I have a common problem. Windows 10 Not Detecting Second Hard Drive Full Format takes many hours!When you are done, reboot and your newly prepared hard drive should show up in My Computer as an empty unit ready for use.
Within 1 minute everything was back to normal. his comment is here It did read 60 gigs at first before I cloned my other 40 gig drive to the 60 gig drive. plz be as analytical as you can because i am totally new to this one thanx for your helpBilly on October 10, 2007 10:51 pm Ed: It seems that A Full Format will do a Quick Format, then go though every sector of the drive and test it, marking off any faulty ones (very rare) so they won't be used. Install/diagnostic/repair Software From Seagate
If the troublesome HDD is not showing up here, it has a major hardware problem because the BIOS cannot communicate with it at all. Both the internal drive & hard drive enclosure units are both brand new. I did try the disk management route but the external drive not recognized in either My Computer, on the system tray or in disk management, hence I cannot partition it.It sounds this contact form I have built a new system, and am struggling with a disappearing SSD.
Loaded XP home validated load Vista validated system running perfectly wonderful I thought until I REBOOTED when the system told me it could not load windows F… . Hard Drive Shows Up In Bios But Not Windows 8 i've restarted my computer but it doesnt take any effect. MANY THANKS!
Disabling the raid on the port would allow windows to see the drive and partition it. If I disconnect the drive the unusually very long pause between windows loading and the welcome screen also doesn't happen. Since this seems to be a very common problem, I wonder why Crucial and others aren't addressing this problem with new firmware. Installing Second Sata Hard Drive Without Raid Click on Start at bottom left and in the menu RIGHT-click on My Computer and choose "Manage" from the mini-menu to open a new window.
I had no success getting the drive to work in Windows 8 and (maybe of course) it doesnt see it now. The SATA drive in BIOS appeared fine, heck, I even booted into Windows 7 setup CD and PARTITIONED and FORMATTED the drive then exited the Windows 7 setup. AnonymousMar 31, 2010, 6:05 AM I also have the problem with a new SATA drive being seen in BIOS but not in Windows Device Manager. navigate here Windows Vista does not have any issue with big drives.
The enumeration order may change over time between system boots, depending on timing factors such as aging hard disks taking slightly longer to spin up. When i run your program, on windowsxp, as i get to the point to restore the disk capacity I get the message: Reported capacity:33.820GB; Factory capacity: -1 Bytes and cappacity difference: I have tried everything that I could think of, Jumpers, reformat, Partition Magic, plugging in to PC via IDE and nothing has worked. I figured something was bad with the drive so I turned off the pc and hooked in the 2nd drive and tried again.
Removed the new drive and attached via USB to my pc running your Capacity Restore Freeware. Then I connected the battery again and turned on the computer. But there are various places to look, and you have not told us details of all of them. On which drive?4.
Thanksblawson on October 24, 2007 5:31 am You saved me !! Full Format takes many hours!When you are done, reboot and your newly prepared hard drive should show up in My Computer as an empty unit ready for use. IT WORKED SO GOOD THINK YOU skeettasMar 29, 2010, 8:35 AM So I got my new SSD drive. After I ran [email protected] Partition Recovery (part of [emailprotected] freeware bundle), it found out that ~50GB of hard disk space was unallocated.
The computer died and I am trying to install the hard drive on a different computer. i lost 7 GB and now i haven't been able to restore it yet. This will open two panes on the right, each of them scrolling to reveal their whole contents. Yeah, I also wondered about the cables, but all are new Asus SATA 6 GB/s cables, and all appeared to be tightly inserted.
That is, it doesn't have separate SATA data and power connection-- just the motherboard slot. How can I restore its full capacity?" There are several common reasons of why your hard drive might lose some megabytes or even gigabytes: Your Operating System does not support LBA48 And we don't even HAVE a best buy. If the tool fails to restore the original capacity, then the most common reason is that your motherboard is blocking HPA and DCO commands.
Many thanks again PS. The other desktop HDD also became the clone of this one and it started showing 28 MB rpoviding all the data loss.